|
|
******** For Colt and Colt Reproductions ********
|
One Gun
|
Two guns
|
|
CA-1
|
Premium Action. Twelve point action work. It doesn’t get any better than this.
Just read the “Customer Comments”.
|
$95.00
|
$190.00
|
|
CA-2
|
Basic Action. Install lighter springs and remove some of the roughness.
|
$70.00
|
$140.00
|
|
CA-3
|
Forcing Cone. Cut the forcing cone angle to reduce leading and improve accuracy.
|
$20.00
|
$40.00
|
|
CA-4
|
Chamfer Cylinders. Takes the sharp edge off the cylinders to facilitate easier loading of your shells.
|
$20.00
|
$40.00
|
|
CA-5
|
Hone Cylinders. Stops sticky shell ejection.
|
$30.00
|
$60.00
|
|
CA-6
|
Polish Entire Gun. Make your stainless gun look almost like nickel.
|
$50.00
|
$100.00
|
|
CA-7
|
Fix Bad Timing on Used Gun+ Parts if Needed.
|
$50.00
|
$100.00
|
|
CA-8
|
Widen Rear Sight. Done on a mill, not with files.
|
$20.00
|
$40.00
|
|
|
********* For Ruger Single Actions *********
|
One Gun
|
Two Guns
|
|
RA-1
|
Premium Action. Twelve point action work. Critical machining and honing to remove “stacking”. Not everyone does this.
Just read the “Customer Comments”.
|
$95.00
|
$190.00
|
|
RA-2
|
Ultimate Short Stroke. TIG welded not brazed. Link for details.
Old or New Vaquero. Hardened firing pin striker. No one else does this.
|
$265.00
|
$530.00
|
|
RA-3
|
Half Cock Conversion . TIG welded not brazed.
Old or New Vaquero. Hardened firing pin striker. No one else does this.
|
$19500
|
$390.00
|
|
RA-4
|
Forcing Cone. Cut the forcing cone angle to reduce leading and improve accuracy.
|
$20.00
|
$40.00
|
|
RA-5
|
Chamfer Cylinders. Takes the sharp edge of the cylinders to facilitate easier loading of your shells.
|
$20.00
|
$40.00
|
|
RA-6
|
Hone Cylinders. Stops sticky shell ejection.
|
$30.00
|
$60.00
|
|
RA-7
|
Remove Stamping on Barrel. This removes the label on the left side of the old Vaquero, or bottom of New Vaquero in stainless. Blue guns add $125.
|
$45.00
|
$90.00
|
|
RA-8
|
Oversized Cylinder Stop. Sized and polished to fit. Removes rotational play for accuracy.
|
$50.00
|
$100.00
|
|
RA-9
|
Black Powder Ejector. The round one like on 1st Generation Colts.
|
$45.00
|
$90.00
|
|
RA-10
|
Crescent Ejector. No more sore fingers from ejecting shells. Looks good too.
|
$45.00
|
$90.00
|
|
RA-11
|
Polish Stainless Gun Make your stainless gun look almost like nickel.
|
$50.00
|
$100.00
|
|
RA-12
|
Colt Base Pin. Oversized in order to remove cylinder wobble. This piece is lapped and polished before installation. Improves accuracy and looks nice.
|
$35.00
|
$70.00
|
|
RA-13
|
Shorten Base Pin. This will give you 1/4 inch more ejector rod travel and it looks a lot better.
|
$15.00
|
$30.00
|
|
RA-14
|
Free Spin Pawl. Allows cylinder to spin both directions when loading and unloading. $15 on New Vaquero.
|
$50.00
|
$100.00
|
|
RA-15
|
Birds Head grip-frame. Stainless, fit and polished.
|
$200.00
|
$400.00
|
|
RA-16
|
Widen Rear Sight. Done on a mill, not with files.
|
$20.00
|
$40.00
|
|
RA-17
|
Serrate Front Sight. 40 LPI
|
$15.00
|
$30.00
|
|
RA-18
|
Cut screw slots in frame pins.
|
$15.00
|
$30.00
|
